Cisco ASR 907 Hardware Installation Manual Download Page 164 | Manualshive

Page: 164 / 204

background image

To avoid the router booting into ROMMON state, it's highly recommended that you set the boot command
prior to the first reload.

Router(config)# boot system flash bootflash:/Image/asr900rsp3-universalk9.x.x.x.-ext.bin

Saving the Running Configuration to NVRAM

To store the configuration or changes to your startup configuration in NVRAM, enter the copy running-config
startup-config command at the Router# prompt:

Router# copy running-config startup-config

Using this command saves the configuration settings that you created in the router using configuration mode
and the setup facility. If you fail to do this, your configuration will be lost the next time you reload the router.

Safely Powering Off the Cisco ASR 907 Router

This section explains how to shut down the Cisco ASR 907 Router. It is recommended that before turning off
all power to the chassis, you issue the

reload

command. This insures that the operating system cleans up all

the file systems. Once the reload operation is complete, then the Cisco ASR 907 Router can be powered off
safely.

To remove power from the Cisco ASR 907 Router safely, follow this procedure and see the examples:

Procedure

Step 1

Slip on the ESD-preventive wrist strap that was included in the accessory kit.

Step 2

Enter the

reload

command.

Step 3

Confirm the reload command.

Example:

Router#

reload

Proceed with reload? [confirm]
*Sep 7 09:00:40.084 IST:%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload
Command.
Sep 7 09:01:02.649 R1/0:%PMAN-5-EXITACTION: Process manager is exiting: process exit with
reload chassis code

Step 4

After confirming the reload command, wait until the system bootstrap message displays before powering off
the system.

Example:

System Bootstrap, Version 15.6(2r)S, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2015 by cisco Systems, Inc.
Compiled Wed 01-Jul-15 04:19 by sdcunha
Starting Initialization of FMAN0
Loading ucode for FMAN0, size: 31424, ver: 106.04.14
fixup address:7ffff278 contentsoffixup:7ffff000
DCFG_CCSR_PORSR1(cfg_0_9 pins):22FB7F7F
RC Vendor ID[0x8241957]

Cisco ASR 907 Router Hardware Installation Guide

154

Cisco Router Initial Configuration

Saving the Running Configuration to NVRAM

«
...
162
163
164
165
166
...
»

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

Brand: Magnat Audio Pages: 2

Brand: Ubiquiti Pages: 40

Brand: Vivotek Pages: 136

Fast SwitchHub-8mi SNMP

Brand: Accton Technology Pages: 13

Brand: XMOS Pages: 6

Brand: Ruckus Wireless Pages: 2

Brand: Rosewill Pages: 10

OP-8000-EDFA-1U Series

Brand: Optostar Pages: 9

Fan Tray 8820-S2-900

Brand: Paradyne Pages: 6

Brand: Eneo Pages: 68

Brand: Moxa Technologies Pages: 51

Brand: Pakedge Device & Software Pages: 14

Brand: RR-Concepts Pages: 12

Brand: Comelit Pages: 140

TigerSwitch 100 SMC6924VF

Brand: SMC Networks Pages: 174

Brand: IBM Pages: 168

Brand: Clas Ohlson Pages: 4

Brand: WIN Enterprises Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands