Cisco ASR 907 Hardware Installation Manual Download Page 192

Page: 192 / 204

Description (two LEDs for each port)

Color/State

LED

Not enabled

Off

Sync status (SYNC)

Free run

Yellow

Holdover

Flashing
yellow

Locked to source

Green

USB activity

Flashing green

USB flash (MEM)

Out of service/not configured

Off

BITS

Fault or loop condition

Amber

In frame/working properly

Green

ASR900-RSP3C-400-W LED Fault Condition

The PWR and STAT LEDs are available on the front panel. These LEDs provide power on the board (PWR)
and overall router health (STAT) status. During power up state, these LEDs provide booting status and report
errors.

The digital code signing functionality validates the integrity and authenticity of the ROMMON image before
booting it.

Note

Table 34: ASR900-RSP3A-400-W LED

Comment

Indication

STAT LED
State

PWR LED
State

Image validation failed. System is in hung
state.

Power is OK and the
field-programmable gate array (FPGA)
is nfigured successfully, but FPGA
image validation failed.

Red

Light
Green

Cisco ASR 907 Router Hardware Installation Guide

182

Troubleshooting

ASR900-RSP3C-400-W LED Fault Condition

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands