Chicco 06620, Instructions For Use Manual

Page: 31 / 220

30 31
- Periodically inspect mains adapters (1). If
the power cord or plastic parts show signs of
damage, do not use them and contact a qualified
technician.
- Do not leave mains adapters (1) plugged into
the outlet when devices are not in use and/or not
connected to the mains adapters (1)
2.2.2 Modes of use - Switching on and
Adjustment
Parent unit (primarily in receiver mode) parent
unit on/off in Baby Monitor mode
Press the on/off button (2) for about 3 seconds.
The parent unit (primarily in receiver mode) will
switch on in Baby Monitor mode.
The power and link indicator light (12) will begin
to flash green and the display (5) will show the
icon to indicate that the parent unit is attempting
to establish a connection with the baby unit.
Once connection has been established between
the 2 units,
will be shown and the power and
link indicator light (12) will light up steady green.
Keep the button (2) pressed for 3 seconds until
the green power and link indicator (12) switches
off. The parent unit (primarily in receiver mode)
will switch off in Baby Monitor mode.
A prolonged beep will be heard when switching
the parent unit on and off in Baby Monitor mode.
Switching on/off the parent unit in Reminder
mode
Press the parent unit on/off button (2) for 1
second to switch on Reminder mode.
Note: keep the on button (2) pressed for no more
than 1 second; otherwise, the unit may switch on
in Baby Monitor mode.
Press the parent unit on/off button (2) again for 1
second to switch off Reminder mode.
A short beep will be heard when switching the
parent unit on and off in Reminder mode.
Volume adjustment + - of the parent unit
loudspeaker
The +,- volume adjustment buttons (6) regulate
the volume of sounds emitted by the baby unit
loudspeaker when the unit is in Baby Monitor
mode.
Press + and – (6) to regulate parent unit
loudspeaker (11) volume and select the desired
level.
The unit offers up to 10 volume setting levels. The
factory set volume level is 5.
Press the “+” button (6) to increase one level.
Press the “-“ (6) button once to decrease one
level.
The change in the volume level will
be shown on the display (5)
Note: The volume adjustment icon includes 5
notches: each notch lights up after 2 presses of
the +/- button (6).
A beep will be heard each time volume is
increased or decreased by a level.
A double beep will be heard each time the
maximum or minimum level is met.
Parent/baby unit communication Talk Function
The ‘talk’ function makes it possible for parents
to communicate with the child when the unit is in
Baby Monitor mode.
Press and hold the button (4) and talk near the
parent unit microphone (10).
When the talk function is on, it is not possible
to hear sounds from the baby unit on the parent
unit.
ATTENTION: when using the ‘Talk’ function, avoid
talking too close to the parent unit microphone
(10) or the baby unit will receive very high
intensity sounds.
ATTENTION: do not press the talk button (4)
when the two units are in the same room or are
less than 3 metres apart; doing so could cause
noises or a hissing sound.
Vibration Alarm function
This function is activated in Baby Monitor mode
from the internal parent unit menu.
When medium-high intensity sounds come
from the baby unit, the unit begins to vibrate,
allowing the parent to be notified when the level
of loudspeaker (11) volume on the parent unit is
set to a minimum.
When this function is set, the
icon is shown
on the display.
For setting details, see Paragraph 3.2.1.
Voice Activation function
In Baby Monitor mode, the parent unit can
operate in continuous transmission mode or in
voice activation mode.
The Voice Activation function is activated from
the internal parent unit menu.
The parent unit loudspeaker (11) interrupts the
reproduction of any sounds emitted from the
child that are below the factory set default voice
activation threshold, while all sounds above the
threshold are reproduced.
When this function is set, the
icon is shown
on the display.
For setting details, see Paragraph 3.2.2.
Reminder Setting
To help organise the family’s days, it is possible
to set 5 acoustic reminders for meals, fever
measuring, medicine, diaper change and sleep
from the internal parent unit menu. This function
is available both when the unit is in Baby Monitor
or Reminder mode.
When reminders are set, the display shows the
relative icons
For setting details, see Paragraph 3.2.4.
After activation of each reminder, a countdown
starts until a warning beep is heard relative to the
reminder expiry. The beep is also accompanied on
the display by a flashing relative reminder icon.
The beep will last 10 seconds followed by a
5 minutes pause, during which the icon will
continue to flash on the display.
This cycle will continue until the reminder is
deactivated via pressing the button (7).
Luminous and acoustic operating status
indicators:
· The power and link indicator light (12) supplies 3
different pieces of information:
- Indication that the device is on in Baby Monitor
mode and properly connected to baby unit:
the indicator light (12) will light up steady green.
- Indication of loss or absence of link with the
baby unit during operation in Baby Monitor mode:
the indicator light (12) lights up green, starts to
flash and the display (5) shows the icon and,
after 1 seconds, 2 consecutive beeps per second