Chicco 06620, Instructions For Use Manual

Page: 30 / 220

30 31
Luminous operating status indicators
· The power and link indicator light (12) supplies 3
different pieces of information:
- Indication that the device is on in Baby Monitor
mode and properly connected to parent unit:
the indicator light (12) will light up steady green.
- Indication of loss or absence of link with the
parent unit during operation in Baby Monitor
mode:
the indicator light (12) will light up green and
begin to flash.
As soon as the link with the parent unit is restored,
the indicator light (12) will light up steady green.
NOTE: when the baby unit switches on, it
searches for the channel to link with the parent
unit; therefore the indicator light (12) will flash
green until a link is established.
- Indication that the unit is off in Baby Monitor
mode or on in Music mode.
the indicator light (12) will switch off.
· The Alkaline battery status indicator light (13)
supplies 2 different pieces of information:
-Indication that Alkaline batteries are almost flat:
the indicator light (13) will light up red and begin
to flash.
- Alkaline batteries charged or operation via
mains adapter (1):
the indicator light (13) will switch off.
2.2 Parent unit (primarily in receiver mode)
2.2.1 Power and recharging:
Power via supplied rechargeable 3.7V 800mAh
lithium-ion battery (18) or via 100-240V~
50/60Hz /6V
mains adapter (1).
ATTENTION. The charging of rechargeable
batteries should only be done via the supplied
mains adapter (1) and can be performed both if
the parent unit is switched on and if the parent
unit is off.
In the event of power with mains adapter (1) or
rechargeable lithium-ion battery charging:
- insert the mains adapter jack (1) in the power
connector (19) on the side of the unit
- verify that the voltage corresponds to the rating
plate of the previously indicated adapters.
- insert the mains adapter plug in an easily
accessible power socket.
Attention:
- The mains adapter cord (1) may constitute a risk
of strangulation, keep out of reach of children.
- Periodically inspect mains adapters (1). If
the power cord or plastic parts show signs of
damage, do not use them and contact a qualified
technician.
- Do not leave mains adapters (1) plugged into
the outlet when devices are not in use and/or not
connected to the mains adapters (1)
2.2.2 Modes of use - Switching on and
Adjustment
Parent unit (primarily in receiver mode) parent
unit on/off in Baby Monitor mode
Press the on/off button (2) for about 3 seconds.
The parent unit (primarily in receiver mode) will
switch on in Baby Monitor mode.
The power and link indicator light (12) will begin
to flash green and the display (5) will show the
icon to indicate that the parent unit is attempting
to establish a connection with the baby unit.
Once connection has been established between
the 2 units,
will be shown and the power and
link indicator light (12) will light up steady green.
Keep the button (2) pressed for 3 seconds until
the green power and link indicator (12) switches
off. The parent unit (primarily in receiver mode)
will switch off in Baby Monitor mode.
A prolonged beep will be heard when switching
the parent unit on and off in Baby Monitor mode.
Switching on/off the parent unit in Reminder
mode
Press the parent unit on/off button (2) for 1
second to switch on Reminder mode.
Note: keep the on button (2) pressed for no more
than 1 second; otherwise, the unit may switch on
in Baby Monitor mode.
Press the parent unit on/off button (2) again for 1
second to switch off Reminder mode.
A short beep will be heard when switching the
parent unit on and off in Reminder mode.
Volume adjustment + - of the parent unit
loudspeaker
The +,- volume adjustment buttons (6) regulate
the volume of sounds emitted by the baby unit
loudspeaker when the unit is in Baby Monitor
mode.
Press + and – (6) to regulate parent unit
loudspeaker (11) volume and select the desired
level.
The unit offers up to 10 volume setting levels. The
factory set volume level is 5.
Press the “+” button (6) to increase one level.
Press the “-“ (6) button once to decrease one
level.
The change in the volume level will
be shown on the display (5)
Note: The volume adjustment icon includes 5
notches: each notch lights up after 2 presses of
the +/- button (6).
A beep will be heard each time volume is
increased or decreased by a level.
A double beep will be heard each time the
maximum or minimum level is met.
Parent/baby unit communication Talk Function
The ‘talk’ function makes it possible for parents
to communicate with the child when the unit is in
Baby Monitor mode.
Press and hold the button (4) and talk near the
parent unit microphone (10).
When the talk function is on, it is not possible
to hear sounds from the baby unit on the parent
unit.
ATTENTION: when using the ‘Talk’ function, avoid
talking too close to the parent unit microphone
(10) or the baby unit will receive very high
intensity sounds.
ATTENTION: do not press the talk button (4)
when the two units are in the same room or are
less than 3 metres apart; doing so could cause
noises or a hissing sound.
Vibration Alarm function
This function is activated in Baby Monitor mode
from the internal parent unit menu.
When medium-high intensity sounds come
from the baby unit, the unit begins to vibrate,
allowing the parent to be notified when the level
of loudspeaker (11) volume on the parent unit is
set to a minimum.
When this function is set, the
icon is shown
on the display.
For setting details, see Paragraph 3.2.1.