Chevrolet 2011 Corvette Owner'S Manual Download Page 56 | Manualshive

Page: 56 / 436

Chevrolet 2011 Corvette Owner'S Manual Download Page 56

Black plate (24,1)

Chevrolet Corvette Owner Manual - 2011

2-24

Keys, Doors and Windows

The parts of the manual convertible
top that are used when lowering and
raising it are:

A. Front Edge of the

Convertible Top

B. Rear Edge of the

Convertible Top

C. Tonneau Cover

Notice:

Leaving the convertible

top down and exposing the
interior of your vehicle to outdoor
conditions may cause damage.
Always close the convertible top
if leaving your vehicle outdoors.

Notice:

Lowering the convertible

top when there are objects in
the storage area could damage it
or break the glass rear window.
Always verify that no objects are
in the storage area before
lowering the convertible top.

Notice:

Lowering the convertible

top if it is damp, wet, or dirty
can cause stains, mildew, and
damage to the inside of your
vehicle. Dry off the convertible
top before lowering it.

Notice:

If you lower the

convertible top on your vehicle
in cold weather (-18°C (0°F)
or lower), you may damage
convertible top components. Do
not lower the top in cold weather.

Notice:

If you raise or lower the

convertible top while the vehicle
is in motion, you could damage
the top or the top mechanism.
The repairs would not be covered
by your warranty. Always put
an automatic transmission in
P (Park) or a manual transmission
in Neutral before raising or
lowering the convertible top.

Lowering the Manual
Convertible Top

1. Park on a level surface.

Shift an automatic transmission
into P (Park) and set the
parking brake. Shift a manual
transmission into N (Neutral) and
set the parking brake.

2. Make sure the ignition is off.

3. Make sure the trunk is closed.

«
...
54
55
56
57
58
...
»

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments