Chevrolet 2011 Corvette Owner'S Manual Download Page 38 | Manualshive

Page: 38 / 436

Chevrolet 2011 Corvette Owner'S Manual Download Page 38

Black plate (6,1)

Chevrolet Corvette Owner Manual - 2011

2-6

Keys, Doors and Windows

9. To program additional

transmitters, repeat Step 7.
Press Acc. on the ignition switch
if programming is complete.

10. Press

K

on each newly

programmed transmitter to
complete the process.

Programming without a
Recognized Transmitter

This procedure requires three
10-minute cycles to complete the
programming process. United
States owners are permitted to
program a new transmitter to
their vehicle when a recognized
transmitter is not available. The
Canadian immobilizer standard
requires that Canadian owners see
their dealer for programming new
transmitters when two recognized
transmitters are not available.

1. The vehicle must be off.

2. Place the new transmitter in

the glove box transmitter pocket
with the buttons facing the
passenger side.

3. Insert the vehicle key into the

key cylinder located above the
license plate.

4. Open the hatch/trunk.

5. Turn the key five times within

five seconds.

6. The DIC message displays

OFF-ACCESSORY TO LEARN.

7. Press Acc. on the ignition

switch.

8. The DIC reads WAIT

10 MINUTES and counts down
to zero.

9. The DIC displays

OFF-ACCESSORY TO LEARN
again.

10. Press Acc. on the ignition

switch.

11. Steps 8, 9, and 10 will be

repeated two more times.

12. A beep sounds and the DIC

reads READY FOR FOB #1. All
previously known transmitter
programming has been erased.

13. A beep sounds once

programming in complete.
The DIC displays READY
FOR FOB #2.

«
...
36
37
38
39
40
...
»

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments