manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 157 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 157

Black plate (35,1)

Chevrolet Corvette Owner Manual - 2011

Instruments and Controls

5-35

If the ignition is on and the HUD
image cannot be seen, check to
see if:

.

Something is covering the
HUD unit.

.

The HUD dimmer control is
adjusted properly.

.

The HUD image is adjusted
to the proper height.

.

Ambient light is low, in the
direction the vehicle is facing.

.

A fuse is blown. See

Fuses and

Circuit Breakers on page 10

‑

51

.

Keep in mind that the windshield is
part of the HUD system. See

Windshield Replacement on
page 10

‑

47

.

Vehicle Messages

Messages displayed on the DIC
indicate the status of the vehicle
or some action may be needed
to correct a condition. Multiple
messages may appear one after
another.

The messages that do not
require immediate action can be
acknowledged and cleared by
pressing the RESET button.

The messages that require
immediate action cannot be cleared
until that action is performed. All
messages should be taken seriously
and clearing the messages does not
correct the problem.

Battery Voltage and
Charging Messages

BATTERY SAVER ACTIVE

This message displays when the
vehicle has detected that the battery
voltage is dropping beyond a
reasonable point. The battery saver
system starts reducing certain
features of the vehicle that you may
be able to notice. At the point that
features are disabled, this message
is displayed. It means that the
vehicle is trying to save the charge
in the battery. Turn off unnecessary
accessories to allow the battery to
recharge.

BATTERY VOLTAGE HIGH

See

Voltmeter Gauge on page 5

‑

15

.

BATTERY VOLTAGE LOW

See

Voltmeter Gauge on page 5

‑

15

.

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments