manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 313 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 313

Black plate (23,1)

Chevrolet Corvette Owner Manual - 2011

Vehicle Care

10-23

Automatic Transmission
Fluid

How to Check Automatic
Transmission Fluid

It is not necessary to check
the transmission fluid level.
A transmission fluid leak is the
only reason for fluid loss. If a
leak occurs, take the vehicle to
the dealer service department
and have it repaired as soon as
possible.

The vehicle is not equipped with
a transmission fluid level dipstick.
There is a special procedure for
checking and changing the
transmission fluid. Because this
procedure is difficult, this should
be done at the dealer service
department. Contact the dealer for

additional information or the
procedure can be found in the
service manual. To purchase a
service manual, see

Service

Publications Ordering Information
on page 13

‑

15

.

Notice:

Use of the incorrect

automatic transmission fluid
may damage the vehicle, and the
damages may not be covered by
the vehicle warranty. Always use
the automatic transmission fluid
listed in

Recommended Fluids

and Lubricants on page 11

‑

6

.

Change the fluid and filter at the
intervals listed in

Scheduled

Maintenance on page 11

‑

2

, and

be sure to use the fluid listed in

Recommended Fluids and
Lubricants on page 11

‑

6

.

Manual Transmission
Fluid

It is not necessary to check the
manual transmission fluid level.
A transmission fluid leak is the
only reason for fluid loss. If a leak
occurs, take the vehicle to the
dealer service department and
have it repaired as soon as
possible. See

Recommended Fluids

and Lubricants on page 11

‑

6

for

the proper fluid to use.

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments