Chevrolet 2011 Corvette Owner'S Manual Download Page 46 | Manualshive

Page: 46 / 436

Chevrolet 2011 Corvette Owner'S Manual Download Page 46

Black plate (14,1)

Chevrolet Corvette Owner Manual - 2011

2-14

Keys, Doors and Windows

Testing the Alarm

To test the system use the following
procedure.

1. Make sure the trunk lid/hatch is

latched.

2. Lower the window on the

driver door.

3. Manually arm the system.

4. Close the doors and wait

30 seconds.

5. Reach through the open window

and manually pull the release
lever on the floor.

6. Press the unlock button on the

transmitter to turn off the alarm.

If the alarm does not sound, check
to see if the horn works. The horn
fuse may be blown. See

Fuses and

Circuit Breakers on page 10

‑

51

.

If the horn works, but the alarm
does not go off, see your dealer.

Disarming the System

Press the unlock button on the RKE
transmitter or squeeze the door
handle sensor while the transmitter
is near the vehicle to unlock a door.
Unlocking a door any other way sets
off the alarm. If the alarm sounds,
press the unlock button on the RKE
transmitter to disarm it.

Do not leave the key or device
that disarms or deactivates the
theft-deterrent system in the vehicle.

Immobilizer

See

Radio Frequency Statement on

page 13

‑

19

for information

regarding Part 15 of the Federal
Communications Commission (FCC)
rules and Industry Canada
Standards RSS-210/220/310.

Immobilizer Operation

The vehicle has a passive
theft-deterrent system.

The system is automatically armed
when the ignition is turned off.

The immobilization system is
disarmed when the ignition is turned
to OFF/ACCESSORY or START and
a valid transmitter is found in the
vehicle.

You do not have to manually arm or
disarm the system.

«
...
44
45
46
47
48
...
»

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments