Home
/
Chevrolet
/
2011 Corvette
/
Owner'S Manual

Chevrolet 2011 Corvette, Owner'S Manual, Page: 321 / 436

Share

Page: 321 / 436

Chevrolet 2011 Corvette Owner'S Manual Download Page 321

Black plate (31,1)

Chevrolet Corvette Owner Manual - 2011

Vehicle Care

10-31

Checking Coolant

The vehicle must be on a level
surface when checking the coolant
level.

Check to see if coolant is visible in
the coolant surge tank. If the coolant
inside the coolant surge tank is
boiling, do not do anything else until
it cools down. If coolant is visible
but the coolant level is not at or
above the FULL COLD mark, add a
50/50 mixture of clean, drinkable
water and DEX-COOL coolant at the
coolant recovery tank, but be sure
the cooling system is cool before
this is done. See

Engine Coolant on

page 10

‑

29

for more information.

The engine coolant surge tank is
located toward the rear of the
engine compartment on the driver
side of the vehicle. See

Engine

Compartment Overview on
page 10

‑

10

for more information on

location.

When the engine is cold, the coolant
level should be at the FULL COLD
mark on the coolant surge tank.

When the engine is hot, the level
could be higher than the FULL
COLD line. If the coolant is below
the FULL COLD line when the
engine is hot, there could be a leak
in the cooling system.

If the coolant is low, add the coolant
or take the vehicle to a dealer for
service.

«
...
319
320
321
322
323
...
»

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments