manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 287 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 287

Black plate (53,1)

Chevrolet Corvette Owner Manual - 2011

Driving and Operating

9-53

There is also a manual fuel door
release tab. It is located against the
upper trim in the rear compartment
on the driver side of the vehicle. Pull
the tab to release the fuel door.

To remove the fuel cap, turn it
slowly counterclockwise.

While refueling, let the cap hang by
the tether below the fuel fill opening.

{

WARNING

Fuel can spray out on you if you
open the fuel cap too quickly.
If you spill fuel and then
something ignites it, you could
be badly burned. This spray can
happen if the tank is nearly full,
and is more likely in hot weather.
Open the fuel cap slowly and wait
for any hiss noise to stop. Then
unscrew the cap all the way.

Be careful not to spill fuel. Do not
top off or overfill the tank and wait
a few seconds after you have
finished pumping before removing
the nozzle. Clean fuel from painted
surfaces as soon as possible. See

Exterior Care on page 10

‑

87

.

When replacing the fuel cap, turn
it clockwise until it clicks. Make
sure the cap is fully installed. The
diagnostic system can determine if
the fuel cap has been left off or
improperly installed. This would
allow fuel to evaporate into the
atmosphere. See

Malfunction

Indicator Lamp on page 5

‑

18

.

The CHECK GAS CAP message
displays on the Driver Information
Center (DIC) if the fuel cap is not
properly installed. See

Fuel System

Messages on page 5

‑

41

for more

information.

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments