manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 331 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 331

Black plate (41,1)

Chevrolet Corvette Owner Manual - 2011

Vehicle Care

10-41

Replacing Brake System Parts

The braking system on a vehicle is
complex. Its many parts have to be
of top quality and work well together
if the vehicle is to have really good
braking. The vehicle was designed
and tested with top-quality brake
parts. When parts of the braking
system are replaced

—

for example,

when the brake linings wear down
and new ones are installed

—

be

sure to get new approved
replacement parts. If this is not
done, the brakes might not work
properly. For example, if someone
puts in brake linings that are wrong
for the vehicle, the balance between
the front and rear brakes can
change

—

for the worse. The

braking performance expected can
change in many other ways if the
wrong replacement brake parts are
installed.

Brake Fluid

The brake master cylinder reservoir
is filled with DOT 3 brake fluid. See

Engine Compartment Overview on
page 10

‑

10

for the location of the

reservoir.

There are only two reasons why the
brake fluid level in the reservoir
might go down:

.

The brake fluid level goes down

because of normal brake lining
wear. When new linings are
installed, the fluid level goes
back up.

.

A fluid leak in the brake
hydraulic system can also cause
a low fluid level. Have the brake
hydraulic system fixed, since a
leak means that sooner or later
the brakes will not work well.

Do not top off the brake fluid.
Adding fluid does not correct a leak.
If fluid is added when the linings
are worn, there will be too much
fluid when new brake linings are
installed. Add or remove brake fluid,
as necessary, only when work is
done on the brake hydraulic system.

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments