manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 280 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 280

Black plate (46,1)

Chevrolet Corvette Owner Manual - 2011

9-46

Driving and Operating

Resuming a Set Speed

If the cruise control is set at a
desired speed and then the brakes
are applied, the cruise control is
disengaged without erasing the set
speed from memory.

Once the vehicle speed reaches
about 40 km/h (25 mph) or more,
move the cruise control switch
briefly from

R

to

S

. The vehicle

returns to the previous set speed
and stays there.

If the switch is held at resume/
accelerate, the vehicle keeps going
faster until the switch is released or
the brake is applied. Do not hold the
switch at resume/accelerate, unless
you want the vehicle to go faster.

Increasing Speed While Using
Cruise Control

If the cruise control system is
already activated,

.

Use the accelerator pedal to get
to the higher speed. Press

J

at

the end of the lever, then release
the button and the accelerator
pedal. If the accelerator pedal is
held longer than 60 seconds,
cruise control will turn off.

.

Move the cruise switch from

R

to

S

. Hold it there until desired

speed is reached, and then
release the switch.

.

To increase the vehicle speed in
small amounts, move the switch
briefly to

S

. Each time this is

done, the vehicle goes about
1.6 km/h (1 mph) faster.

Reducing Speed While Using
Cruise Control

If the cruise control system is
already activated,

.

Press and hold the set button
until the lower speed desired is
reached, then release it.

.

To slow down in small amounts,
briefly press

J

. Each time this

is done, the vehicle goes about
1.6 km/h (1 mph) slower.

Passing Another Vehicle While
Using Cruise Control

Use the accelerator pedal to
increase the vehicle speed. When
you take your foot off the pedal,
the vehicle will slow down to the
previous set cruise speed.

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments