manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 158 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 158

Black plate (36,1)

Chevrolet Corvette Owner Manual - 2011

5-36

Instruments and Controls

SERVICE CHARGING SYSTEM

If this message displays while you
are driving, there may be a problem
with the electrical charging system.
It could mean that there is a loose
or broken drive belt or that there is
another electrical problem. Have the
vehicle checked right away by your
dealer. Driving while this message is
on could drain the battery.

If you must drive a short distance
with the message on, be certain to
turn off the vehicle's accessories,
such as the radio and air
conditioner.

Multiple chimes sound when this
message is displayed.

To acknowledge the message, press
the RESET button. The message
reappears every 10 minutes until
this condition changes.

Brake System Messages

ABS (Antilock Brake System)
ACTIVE

This message displays when the
Antilock Brake System (ABS) is
adjusting brake pressure to help
avoid a braking skid.

Slippery road conditions may exist
if this message is displayed, so
adjust your driving accordingly.
The message stays on for a few
seconds after the system stops
adjusting brake pressure. See

Antilock Brake System (ABS) on
page 9

‑

34

for more information.

CHANGE BRAKE PADS

On vehicles with electronic brake
pad wear sensors, this message will
be displayed when the pads are
worn. See your dealer for service.

CHECK BRAKE FLUID

This message displays, a sound
will be heard, and the brake system
warning light on the instrument
panel cluster turns on if the ignition
is on to inform the driver that the
brake fluid level is low. See

Brake

System Warning Light on
page 5

‑

21

. Have the brake system

serviced by your dealer as soon as
possible. See

Brakes on

page 10

‑

38

.

SERVICE ANTILOCK BRAKES

If this message displays while
you are driving, stop as soon as
possible and turn the ignition off.
Then start the engine again to reset
the system. If the message stays
on, or comes back on again while
you are driving, the vehicle is in
need of service. See your dealer.
If the antilock brake system (ABS)
warning light is on and the regular
brake system warning light is not

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments