manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 160 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 160

Black plate (38,1)

Chevrolet Corvette Owner Manual - 2011

5-38

Instruments and Controls

TOO COLD TO MOVE TOP

This message displays and a
sound will be heard when the
power convertible top button is
pressed and the power convertible
top pump motor temperature is
below

−

20°C (

−

4°F). Wait for the

power convertible top pump motor
to warm up before using the power
convertible top.

TOP MOTOR OVER
TEMPERATURE

This message displays and a
sound will be heard when the
power convertible top button is
pressed and the power convertible
top pump motor temperature is over
105°C (221°F). Wait for the power
convertible top pump motor to cool
down before using the power
convertible top.

TOP NOT SECURE

This message displays and a
sound will be heard when the
power convertible top button is
released before the top open or
close operation is complete or if the
top is closed without the header
latch engaged. Press and hold the
convertible top button to fully open
or close the top, and make sure that
the header latch is engaged after
the top is closed.

UNLATCH HEADER TO
MOVE TOP

This message displays and a
sound will be heard if you try to
lower the convertible top without
first unlocking the top. Move
the latch handle to unlock the
convertible top. See

Convertible Top

on page 2

‑

23

.

Cruise Control Messages

CRUISE DISENGAGED

This message displays briefly when
you disengage the cruise control
system by stepping on the brake on
an automatic transmission vehicle or
the clutch on a manual transmission
vehicle, or by turning off the cruise
control switch. See

Cruise Control

on page 9

‑

45

for more information.

CRUISE SET TO XXX MPH
(XXX km/h)

See

Cruise Control on page 9

‑

45

.

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments