manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 264 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 264

Black plate (30,1)

Chevrolet Corvette Owner Manual - 2011

9-30

Driving and Operating

See

Traction Control System (TCS)

on page 9

‑

36

Traction Control

System (TCS).

The Manual Paddle Shift system
can be deactivated by moving the
shifter from S (Sport Mode) back
to D (Drive), or by holding either
up

‐

shift paddle for more than

one second.

The driver may choose to briefly
activate the Manual Paddle Shift
system while in D (Drive). Tapping
either the upshift or downshift
controls will place the transmission
in Manual Paddle Shift mode. The
driver may then exit Manual Paddle
Shift mode by holding either upshift
control for two seconds. The system
will return to automatic shifting after
10 seconds of cruising at a steady
speed, or when the vehicle comes
to a stop.

While the Manual Paddle Shift
gear selection system is active,
the transmission will automatically
downshift through the gears as the

vehicle slows. The transmission
will select 2 (Second) gear as the
vehicle stops. From a stop, the
vehicle will start from and hold
2 (Second) gear unless the driver
manually paddle shifts into a
different gear or selects D (Drive).
The driver can select 1 (First) gear
for maximum acceleration from
a stop.

When using the Manual Paddle
Shift feature while in S (Sport Mode)
, the current gear will be displayed
in the Driver Information (DIC),
or the Head-Up Display (HUD), if the
vehicle has either of these features.

If the vehicle has a Head-Up
Display (HUD), see

Head-Up

Display (HUD) on page 5

‑

31

.

The Manual Paddle Shift system
will not allow either an up-shift or a
down-shift if the vehicle speed is too
fast or too slow, nor will it allow a
start from 4 (Fourth) or higher gear.

If up-shifting does not occur when
needed, vehicle speed will be
limited to protect the engine.

When the transmission gear does
not respond to a shift change, the
DIC will show an X over the gear
display.

When a requested shift is denied
due to the speed restrictions shown,
the DIC will momentarily show an X
over the gear display and a chime
will sound.

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments