manualshive.com logo in svg

Chevrolet 2011 Corvette, Owner'S Manual, Page: 323 / 436

Share
Download
Chevrolet 2011 Corvette Owner'S Manual Download Page 323

Black plate (33,1)

Chevrolet Corvette Owner Manual - 2011

Vehicle Care

10-33

3. Fill the coolant surge tank with

the proper DEX-COOL coolant
mixture until the level inside
stabilizes at the FULL COLD
mark on the front of the
surge tank.

4. With the coolant surge tank

pressure cap off, start the
engine and let it run until the
upper radiator hose can be felt
getting hot. Any time during this
procedure, watch out for the
engine cooling fan.

By this time, the coolant level
inside the coolant surge tank
may be lower. If the level is
lower, add more of the proper
mixture to the coolant surge tank
until the level stabilizes at the
FULL COLD mark on the coolant
surge tank.

5. Replace the pressure cap. Be

sure the pressure cap is
hand-tight and fully seated.

Check the level in the surge tank
when the system has cooled
down. If the coolant is not at the
proper level, repeat Steps 1
through 4, then reinstall the
pressure cap. If the coolant is
not at the proper level when the
system cools down again, see
the dealer.

Notice:

If the pressure cap is

not tightly installed, coolant loss
and possible engine damage may
occur. Be sure the cap is properly
and tightly secured.

Summary of Contents for 2011 Corvette





















































































































































































































































































































































































































































Reviews:

No comments