Carrier TruVu TV-MPCXP1628-NR Installation And Startup Manual Download Page 84

Page: 84 / 94

Troubleshooting

ruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

Installation and Start-up Guide

To replace the TV-MPCXP1628-NR's fuses

The TV-MPCXP1628-NR has 2 fuses:

Symptoms of a blown fuse:

•

TV-MPCXP1628-NR's power fuse

—The controller’s

LED is not lit.

•

I/O bus edge connector fuse

—

The

LED is not lit on downstream expanders connected to the edge

connector.

NOTE

If the TV-MPCXP1628-NR's power fuse blows but not the I/O bus edge connector fuse, the TV-MPCXP1628-

NR will be off but not the downstream expanders.

If you suspect a fuse is blown, remove the fuse as described below, and use a multimeter to check it. If the fuse is

blown, try to determine why it blew before you replace it. Check the power wiring polarity of the TV-MPCXP1628-NR
and any other devices that share the power supply. Use the same polarity for all of them.

The fuses are fast-acting, 5mm x 20mm glass fuses that you can purchase from one of the following vendors:

Manufacturer

Mfr. Part #

for 2.5A fuse

Mfr. Part #

for 4A fuse

Littelfuse
Bussmann

Belfuse

Optifuse

021702.5HXP
not specified

5SF-2.5-R

FSD-2.5A

0217004.HXP
S500-4-R

5SF 4-R

FSD-4A

Summary of Contents for TruVu TV-MPCXP1628-NR































































































Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands

Carrier TruVu TV-MPCXP1628-NR, Installation And Startup Manual

Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands