Carrier TruVu TV-MPCXP1628-NR Installation And Startup Manual Download Page 33

Page: 33 / 94

Wiring for communications

TruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

Installation and Start-up Guide

Wiring specifications

For...

Use...

Maximum Length

BACnet/IP

Ethernet

CAT5e or higher Ethernet cable

328 feet (100 meters)

MS/TP*

ARCNET*

22 AWG, low-capacitance, twisted, stranded,

shielded copper wire *

2000 feet (610 meters)

For details see the

Open Controller Network Wiring Guide

WARNING

Do not apply line voltage (mains voltage) to the controller's ports and terminals.

To connect the TV-MPCXP1628-NR to the Ethernet

Connect an Ethernet cable to the Gig-E Ethernet port.

NOTE

Be careful NOT to plug your cable into the Service Port.

NOTE

If your system has controllers on different IP subnets separated by an IP router, you must configure one

controller on each subnet as a BACnet Broadcast Management Device (BBMD). Do not configure more than one
BBMD per subnet as this may cause circular routes. See

To set up BACnet Broadcast Management Devices

(BBMDs)

(page 22).

Summary of Contents for TruVu TV-MPCXP1628-NR































































































Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands

Carrier TruVu TV-MPCXP1628-NR, Installation And Startup Manual

Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands