Carrier TruVu TV-MPCXP1628-NR Installation And Startup Manual Download Page 57

Page: 57 / 94

Adjusting the TV-MPCXP1628-NR driver properties

TruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

Installation and Start-up Guide

BACnet Controller Properties

CAUTION

Do not change the settings on this page as it will result in communication failure. Use

the

controller setup pages

(page 61) to change settings and then resolve mismatches in the i-Vu® application.

BACnet Firewall

If this IP controller is accessible from the Internet, you can increase security by enabling its BACnet firewall. When
enabled, this feature prevents the controller from responding to BACnet messages from unidentified sources and

allows communication only with IP addresses that you define. These can be all private IP addresses and/or a list

of IP addresses. Follow the instructions in the i-Vu® interface to set up the BACnet firewall.

Network Diagnostics - Statistics

This page shows the network statistics for each of the TV-MPCXP1628-NR's ports that are in use. This same

information is provided in a

Module Status report

(page 73).

Click the

Error Rate Trend

Packet Rate Trend

link at the bottom of each section to see the statistics displayed

as trend graphs. You can also access these trends by clicking on the driver in the network tree, and then selecting

Trends

Enabled Points

> and the desired trend graph.

Click a port's

Reset

button to set all of the numbers to zero so the counting can start over.

Controller Statistics

Error Counters

Dropped Packets

—

Data packets that could not be delivered.

Route Not Found

—

Packets that could not be delivered because the requested

network does not exist.

Route Unreachable

—

These are routed packets whose destination network is

either busy or offline

Controller Sourced Packets

Shows the number of packets initiated by the TV-MPCXP1628-NR that are not in

response to a request from another device. The numbers in this table will also

appear in the appropriate columns in the

Network Activity

tab.

Summary of Contents for TruVu TV-MPCXP1628-NR































































































Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands

Carrier TruVu TV-MPCXP1628-NR, Installation And Startup Manual

Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands