Carrier TruVu TV-MPCXP1628-NR Installation And Startup Manual Download Page 42

Page: 42 / 94

Wiring inputs and outputs

TruVu™ MPC Controller (

part no. TV-MPCXP1628-NR)

Installation and Start-up Guide

To wire inputs and outputs

WARNING

Do not apply line voltage (mains voltage) to the controller's ports and terminals.

The input terminals are arranged vertically. The ground (

) is below the input terminal (

). Allow .75 in. (19 mm)

extra wire length for the top (+) screw terminal than for the (-) bottom.

CAUTIONS

○

Do not allow more than .125 inch (.3 cm) bare communication wire to protrude.

.125 in.

(.3 cm)

Correct

Incorrect

If bare communication wire contacts the cable's foil shield, shield wire, or a metal surface other than the terminal

block, communications may fail.

Verify that the TV-MPCXP1628-NR's power and communications connections work properly.

Turn

off

the TV-MPCXP1628-NR's power.

Summary of Contents for TruVu TV-MPCXP1628-NR































































































Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands

Carrier TruVu TV-MPCXP1628-NR, Installation And Startup Manual

Search results

Summary of Contents for TruVu TV-MPCXP1628-NR

Reviews:

Related manuals for TruVu TV-MPCXP1628-NR

Brands by name

Popular brands