13
8
7
SCALA: 1:2
DRACO
23.04.2009
DI0966
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
180
Vista in pianta e di fianco senza motore
25
113
72,6
50
325
56
60
SCALA: 1:2
Prodotti Technocity
SL1524
08-02-2002
DI0240
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
VISTA DI FIANCO CON MOTORE
25
15
325
72,6
2 mm
Anchoring the unit SLX24DRACO - SLX24DRACO2
(fig. 6, 7)
Important!
Check the exact anchoring position with respect to the alignment of the sliding gate
• Run the piping and connection wires to the position where the motor is to be
installed.
• Attach the anchor bolts to the base plate ‘
A
’ allowing them to protrude
by
50 mm
and then tighten down using the supplied
M12
nuts.
• Prepare a cement plinth, in the position where the motor is to
be installed, with a depth of
350 mm
(the base should protrude
by about
25 mm
to avoid damage by pools of water building up
under the appliance).
• Insert the base plate making sure that:
- the electrical cables pass through the hole ‘
B
’;
- the anchor bolts ‘
C
’ are immersed into the cement base and the base plate
is perfectly level;
- the four protruding threaded bolts are perpendicular to the base plate;
- the surface area of the base plate is clean and free of cement residue.
If the runner guide already exists the cement base should be extended to take in part of
the runner guide foundation. This will stop the two foundations from giving way separately.
- Unscrew the four
M12
nuts on the four threaded bolts (previously used to block the anchor
bolts) from the base of the anchor plate. Then insert the four washers and allow them to rest
on the nuts.
- Position the geared motor over the four threaded bolts and allow it to rest on the four washers.
- Fasten in to the base using the other four washers and
adjustment nuts supplied with the kit, making sure that the unit remains perfectly level and
stable.
- Adjust the height if the unit using the four grub screws already positioned on the motor. This
will allow you to adjust the height
and position of the motor later on.
Fitting the gear rack
- release the geared motor (fig. 8), lay
the first stretch of the toothed rack
on the pinion and fix it to the gate,
then fasten down all the other parts
along the entire length of the gate.
- after having fastened the toothed
rack, realign the pinion (play of
1 to
2 mm
between the gear runner and
the pinion) using the grub screws at
the base of the geared motor. This
action will prevent the weight of the
sliding gate from damaging the unit
when working.
SCALA: 1:2
Prodotti Cardin
DRACO
24-10-2019
DI0967
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
CONTROPIASTRA DRACO
M12
50 mm
273
64
60
180
56
36
A
C
Poortkant - Strana vrat - Grindsida
portail
255
B
23
6
Manual release is to be carried out with the motor stopped. To release the gate use the manual release key supplied with
the unit. The key should be kept in an easily accessible place.
LEVER ACTIVATED MANUAL MANOEUVRE WITH THE MOTOR RELEASED SLX24DRACO - SLX24DRACO2
2 - RELEASE MEC. REACTIVATED
• Rotate the knob anticlockwise
and replace the lock protection
disk.
- all commands are enabled
-
the automation will start up
again in the repositioning mode.
SBLOCCO SLI
23-05-2018
DI0843
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SBLOCCO MOTORE
2
1
180°
180°
SBLOCCO SLI
23-05-2018
DI0843
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SBLOCCO MOTORE
2
1
180°
180°
1 - MOTOR RELEASED
• Rotate the lock protection
disk, insert the key, rotate it
half a turn anticlockwise
- all commands are inhibited
- the gate can be moved by
hand
ANCHORING
THE UNIT
Plan view
ANCHORING
THE UNIT
Side view
Gate
Base plate
Gear rack
