15
MAINS POWER SUPPLY CONNECTION 230 Vac
• Connect the control and security device wires.
• Run the mains power supply through the cable clamp located on
the bottom right of the main circuit board and to the
separate
3-way
terminal board:
- connect the
neutral
to binding post
N
- connect the
earth
to binding post
- connect
the live
to binding post
L
Electronic programming unit
Instructions for programming the ECU and battery powered
operation can be found in the
MULTI-ECU SOFTWARE
manual
ZVL608
supplied with the automation.
To use the
36 month
or
50000 manoeuvre
guarantee, read the
following notes carefully.
Attention!
Before carrying out any cleaning or maintenance
operations make sure the power is disconnected at the mains,
the motor power cables are disconnected and the batteries
have been disconnected.
Eventual repair work must be carried out by specialised per-
sonnel using original spare parts.
The motor does not normally require particular maintenance; in
any case the
36 month
or
50000 manoeuvre
guarantee is only
valid if the following controls have been observed and eventual
maintenance has been carried out to the machine ‘sliding gate’:
- check the straightness of the toothed rack, make sure the teeth
fit correctly in the pinion throughout its entire length; in particular
the gear rack must have a cross section of
20 x 20 mm
;
- check the play of the gear rack - pinion (
1-2 mm
see fig. 7/10);
- periodically check the moving parts for wear and tear and
grease if required, using lubricants which maintain their friction
levels unaltered throughout time and are suitable for temper-
atures of
-20 to +70°C
;
- check the battery charge level.
These checks must be written down as they are paramount in
validating the guarantee.
SCREW OPERATED MANUAL RELEASE SYSTEM
SLX1524 - SLX824
To release the unit
1. Lower the lock protection ‘
A
’ on the release knob, insert the
key ‘
B
’ and rotate it through 180 degrees clockwise. The knob
is now free and can be rotated.
2. Rotate the knob ‘
C
’ clockwise until reaches its travel limit.
The geared motor is now released and the gate can be moved
manually.
Attention!
Do not force the knob to exceed the travel limit.
To relock the unit
1. Rotate the knob ‘
D
’ anticlockwise until it blocks completely.
2. Rotate the key anticlockwise and position the lock protection.
The geared motor is now locked and the gate may be used
normally.
Once the system has been reset store the key in a safe place.
Attention!
Never use the manual release mechanism
while the gate is in operation.
Moving the gate manually
will force the encoder to
lose the position of the gate. To reset the control, once
the gate has been relocked, you will need to give 3
or more movement commands so that the gate leaf
will reach the travel limit enough times to position
itself correctly.
Access to the electronic card
Attention!
Before opening the cover make sure that the power
has been switched off at the mains. To access the motor loosen
the two screws ‘
A
’ positioned on either end of the cover as
indicated in figure 11.
Attention!
When the power is off the
SLX1024REV
motor is
reversible and requires a force of at least
35 kg
to open the gate.
Important remarks
• After having installed the device,
and before powering
up the programmer
, release the door (manual release
mechanism) and move it manually, checking that it moves
smoothly and has no unusual points of resistance.
• The presence of the electrical current sensor does not
dispense with the obligation to install photoelectric cells
and other safety devices foreseen by the safety standards
in force.
• Before connecting the appliance make sure that the voltage
and frequency rated on the data plate conform to those of
the mains supply.
• The motor’s power cable must be made of polychloroprene
in conformity with the international standard
60245 IEC 57
(e.g.
3 x 1.5 mm
2
H05RN-F).
• The cable may only be replaced by qualified technicians.
• An all pole trip switch with at least
3 mm
between the
contacts must be installed between the unit and the mains
supply.
• Don’t use cables with aluminium conductors; don’t solder
the ends of cables which are to be inserted into the binding
posts; use cables marked
T min 85°C
and resistant to
atmospheric agents.
• The terminal wires must be positioned in such a way that
both the wire and the insulating sheath are tightly fastened.
N
L
Fissaggio placca inferiore
06-03-95
DI0286
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
Collegamento motore
MAINTENANCE
12
ELECTRICAL CONNECTION
Sblocco nuovo “A”
SL1524SB
13-11-2008
DM0801
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SL1524SB
A
Sblocco nuovo “B”
SL1524SB
13-11-2008
DM0802
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SL1524SB
B
180°
Sblocco nuovo “C”
SL1524SB
13-11-2008
DM0803
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SL1524SB
C
Sblocco nuovo “D”
SL1524SB
13-11-2008
DM0804
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A
- 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
SL1524SB
D
5 - 6 turns
5 - 6 turns
SLX1524 - SLX824
OPENING THE GATE BY HAND SLX1024REV
