manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 96

3-24

CHAPTER 3.  REPAIR INSTRUCTION

Fig. 3-24 LCD FRAME COVER, LCD PANEL

(1)-2

(1)-3

(1)-1

NUT PLATE

LCD FRAME 
COVER

BASE PIN

LCD PANEL

BACK LIGHT UNIT

Dowels

Dowels

(2)-1

(2)-2

XA4-9170-359

BLACK

M1.7

(SELF TAP)

3.5mm

q

q

NOTE (Assembling)

In the case of the repair 
service part, it is supplied
with the protection sheet.
Remove the protection 
sheet before use.

2.3.2.2 LCD FRAME COVER, LCD PANEL

(1) LCD FRAME COVER

1. Remove the two screws of 

q

.

2. Remove the NUT PLATE.
3. Remove the LCD FRAME COVER from the LCD PANEL.

(2) LCD PANEL

1. Remove the flexible board of the LCD PANEL.
2. Remove the four dowels, then remove the LCD PANEL.

NOTE (Assembling)

In the case of the repair service part, it is supplied with the protection sheet. Remove the protection sheet
before use.

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands