manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 105

3-33

CHAPTER 3.  REPAIR INSTRUCTION

Adjustment Items

Replacement Part

BATTERY BOX UNIT

DC/DC CONV. UNIT

OPTICAL UNIT

FLASH UNIT

MAIN PCB ASS’Y

LCD PCB ASS’Y

LCD PANEL

BACK LIGHT UNIT

CCD

Adjustment

         

#1

Optical Unit

Adjustment

         

#2

Imaging

Process

Adjustment

         

#3

Pixel Dot

Adjustment

         

#5

Flash

Adjustment

         

#6

LCD

Adjustment

: Adjustment is necessary after replacement.
: Adjustment is necessary after replacement.

(Adjustment is not necessary, only if the adjustment data has been saved and then transferred
after the part is replaced.)

Blank : Adjustment is unnecessary.

∗

 When OPTICAL UNIT is replaced, adjust certainly at the procedure as below.

#1. CCD Adjustment

#2. Optical Unit Adjustment

#3. Imaging Process Adjustment

#4. Color Adjustment

#5. Pixel Dot Adjustment

#6. Flash Adjustment

Color

Adjustment

         

#4

3. Adjustments

3.1 Replacement Parts and Adjustment Items

PowerShot G3 requires electrical adjustments when certain parts are replaced.
The table below indicates the adjustments required for the respective part replacements.
For all other parts not listed below, no electrical adjustments are necessary after replacement.

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands