manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 109

3-37

CHAPTER 3.  REPAIR INSTRUCTION

Personal Computer

USB

INTERFACE CABLE

IFC-300PCU

DIGITAL

Compact Power Adapter

CA-560

CAMERA BODY

50

3.3.3 Preparation

Before starting up the Adjustment Software, follow the preparatory steps below:

1. Obtain all the tools necessary for the adjustment.
2. For the Optical Unit Adjustment, jot down the data written on the Optical Unit. You will need it later.

3. Connect the Camera to the Power Source with the Compact Power Adapter CA-560 & AC Cable.
4. Set the Replay Mode on the camera and turn on.
5. Set the Communication Mode to Normal.

6. Connect the Camera’s Digital terminal to the PC’s USB Port with INTERFACE CABLE IFC-300 PCU.
7. Turn on the camera.

* Perform the preparation in the following order otherwise the camera won’t work properly.

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands