Canon PowerShot G3 Service Manual Download Page 73

Page: 73 / 185

3-1

CHAPTER 3. REPAIR INSTRUCTION

Fig. 3-1 Precaution on flash high tension circuit

1. Before Starting the Repair Work

Be sure to read the following precaution before starting the repair work.

1.1 Precaution on Flash High Tension Circuit

•

When the FRONT COVER UNIT is removed, be sure to discharge the main capacitor.
(Discharging resistor: 1 k

Ω

, approx. 5 W.)

•

First contact the GND

terminal of the main capacitor with the discharging resistor. Then contact the

positive

terminal of the main capacitor.

CAUTION:

Be careful of electric shock because the circuit is the high tension circuit.

1.2 List of Tools

The following tools are used for the re-assembling during service.

(1) List of tools

New

Name of tools

Part No.

Remarks

Screwdriver (Local Purchase)
Tweezers (Local Purchase)
Soldering iron (Local Purchase)

1.3 List of Supplies

The following supplies are used for the re-assembling during service.

(1) List of supplies

New

Name of supplies

Part No.

Remarks

ADHESIVE TAPE, SONY T4000

CY4-6012-000

Fixing the flexible cable

DIA BOND No.1663G

CY9-8129-000

Attaching the parts together

INSULATION TAPE 3M No.56

CY4-6018-000

Used for SIDE COVER FRAME

LOGENEST RAMBDA A-74

CY9-8102-000

Used when exchanging MODE DIAL,
ZOOM LEVER UNIT

FLASH/JACK UNIT

+ terminal

– terminal

Summary of Contents for PowerShot G3


























































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Brands by name

Popular brands

Canon PowerShot G3, Service Manual

Search results

Summary of Contents for PowerShot G3

Reviews:

Brands by name

Popular brands