manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 118

3-46

CHAPTER 3.  REPAIR INSTRUCTION

Personal 
Computer

Power 
Source

48.0cm

AutoFocus Chart (1)

CAMERA
BODY

Tripod

1

Click the “Optical Unit” button.

3.5.2 Optical Unit Adjustment

■

Tools Used

• Personal Computer

• INTERFACE CABLE IFC-300PCU

• Adjustment Software

• AutoFocus Chart

• Compact Power Adapter CA-560

• Tripod

• AC Cable

2

When the message on the right appears, go to 3.

3

1. Place the Auto Focus Chart (1) at 48.0cm away

from the front of the camera finder.
* Place the Auto Focus Chart on a plain color

wall or equivalent.

* Adjust the light so that the brightness of the

chart will be about EV8.5.

2. Adjust the position of the camera finely so that

the center of the Auto Focus Chart is aligned
with the center of the LCD.

3. Click the “ADJUST” button.

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands