manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 63

2-1

CHAPTER 2.  TECHNICAL DESCRIPTION

1. Functions of each unit

1.1 MAIN PCB ASS’Y

1) Driving the CCD Sensor.
2) Conversion of the image signal from the analog signal to the digital signal.
3) Controlling the power supply and the system by CPU. (Refer to Sections 2.1 and 2.2.)
4) Image processing, and reading and writing the image signal to and from the CF card using DSP.

(Refer to Section 2.2.2.)

5) Video output. (Refer to Section 2.2.2.)
6) Microphone input and sound output. (Refer to Section 2.2.3.)

1.2 DC/DC CONVERTER PCB ASS’Y

1) Power supply drive (DC/DC converter).
2) Battery charging control circuit.

1.3 LCD PCB ASS’Y

1) Image display.
2) Backlight for LCD drive.

1.4 TOP MODULE UNIT

1) Operation switch, operation display and finder LED.

1.5 EF FPC

1) Flash control.

1.6 STJ PCB ASS’Y

1) Flash drive and charging circuit for the flash.

Fig. 1

TOP MODULE UNIT

LCD PCB ASS'Y

BUTTON PCB ASS'Y

FLASH UNIT

DC/DC CONVERTER PCB ASS'Y

MAIN PCB ASS'Y

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands