Canon PowerShot G3 Service Manual Download Page 70

Page: 70 / 185

2-8

CHAPTER 2. TECHNICAL DESCRIPTION

Cause and Probable Faulty Part

EF FPC

ACC. SHOE FPC

ACC. CONTACT UNIT

ACC. SHOE PIN

ACC. DETECT PLATE

STJ PCB ASS’Y

MAIN PCB ASS’Y

STJ PCB ASS’Y

MAIN PCB ASS’Y

CF CARD/MICRO DRIVE

CF UNIT

MAIN PCB ASS’Y

MIC. UNIT

STJ PCB ASS’Y

MAIN PCB ASS’Y

SPEAKER UNIT

DC/DC CONVERTER PCB ASS’Y

MAIN PCB ASS’Y

HV FPC

EF FPC

MAIN PCB ASS’Y

EF FPC

TOP MODULE UNIT

MAIN PCB ASS’Y

MODE DIAL BRUSH

TOP MODULE UNIT

MAIN PCB ASS’Y

BATTERY BOX MAIN UNIT

DATE LEAD

HV FPC

EF FPC

MAIN PCB ASS’Y

DC/DC CONVERTER PCB ASS’Y

Problem (when an error code is not displayed)

The External Flash does not fire.

Video output is strange.

Communications with the personal computer is not possible.

The CF card or Micro Drive is not recognized.

Sound cannot be recorded.

Shutter sound/Sound is not played back.

Operations from the Wireless Controller are not accepted.

Buttons do not work.

The Mode dial does not work.

The date setting is not held in memory.

Battery charge error

Summary of Contents for PowerShot G3


























































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Brands by name

Popular brands

Canon PowerShot G3, Service Manual

Search results

Summary of Contents for PowerShot G3

Reviews:

Brands by name

Popular brands