manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 88

3-16

CHAPTER 3.  REPAIR INSTRUCTION

Fig. 3-16 OPTICAL UNIT, FINDER UNIT

Coat it with the Dia bond 1663G

LED 
HOLDER

(1)-6
OPTICAL UNIT

LED HOLDER

LED HOLDER

(1)-5
Flat-head 
screwdriver

(1)-3
Claw

Dowel

(1)-1

(1)-2

(1)-7

(1)-4

(1)-6

(1)-6

(1)-6
FINDER UNIT

XA4-9170-359

BLACK

M1.7

(SELF TAP)

3.5mm

q

q

NOTE (Assembling)

2.2.13 OPTICAL UNIT, FINDER UNIT

(1) OPTICAL UNIT, FINDER UNIT

1. Remove the two screws of 

q

.

2. Slant the FINDER UNIT in the direction of the arrow, and remove the dowel.
3. Remove the claw on the opposite side.
4. Turn over the FINDER UNIT in the direction of the arrow.
5. Push out the LED HOLDER with the use of flat-head screwdriver.
6. Turn over the FINDER UNIT again, pull out the LED HOLDER and remove the FINDER UNIT from the

OPTICAL UNIT.

7. Peel off the portion fixed by the Dia bond, and remove the LED HOLDER from the flexible board.

NOTE (Assembling)

Align the two dowels of the LED HOLDER with the position setting hole of the flexible board and coat it
with the Dia bond 1663G as shown in the figure.

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands