manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 69

2-7

CHAPTER 2.  TECHNICAL DESCRIPTION

3.2 When a Problem Occurs

[Remedy]
• Check for any abnormalities in the mounting of probable faulty parts or connector connections referring

to the table below.

• Try replacing probable faulty parts referring to the table below.

[NOTE]
• Adjustments must be performed after the part has been replaced. For details, see “CH.3  3. Adjustments”

Cause and Probable Faulty Part

DC/DC CONVERTER PCB ASS’Y

MAIN PCB ASS’Y

MAIN DIAL BRUSH

TOP MODULE UNIT

BATTERY BOX MAIN UNIT

BATTERY EJECT SPRING

POWER LEAD

HINGE UNIT

MAIN PCB ASS’Y

EF FPC

LCD PANEL

LCD PCB ASS’Y

BACK LIGHT UNIT

HINGE UNIT

LCD PCB ASS’Y

MAIN PCB ASS’Y

OPTICAL UNIT

MAIN PCB ASS’Y

OPTICAL UNIT

MAIN PCB ASS’Y

ZOOM BRUSH

TOP MODULE UNIT

B/W LCD PANEL

CONTACT RUBBER

TOP MODULE UNIT

MAIN PCB ASS’Y

STJ PCB ASS’Y

DC/DC CONVERTER PCB ASS’Y

TOP MODULE UNIT

Problem (when an error code is not displayed)

The camera does not work.

The image is not displayed on the LCD Monitor.

The image is not reversed even if the LCD Monitor is rotated.

The photograph image is abnormal.

The zoom does not function.

The Display Panel (B/W LCD) is strange.

The Built-in Flash does not fire.

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands