manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 101

3-29

CHAPTER 3.  REPAIR INSTRUCTION

 Fig.3-29 Assembling the CCD HOLDER,SHUTTER UNIT-2

2.3.4.3 Assembling the CCD HOLDER, SHUTTER UNIT-2

(1) Assembling the CCD HOLDER,SHUTTER UNIT-2

1. Hold the portion A and rotate it in the direction of the arrow as far as it can go.
2. Rotate the portion B of the LENS BARREL UNIT in the direction of the arrow as far as it can go.
3. Install the FPC GUIDE.
4. Align the SHUTTER UNIT with the dowel used for position setting.
5. Align the large hole and small hole of the receptacle with the large projection and small projection of the

projected part, and insert the CCD HOLDER UNIT.

6. Install the three screws of 

s

.

NOTE1 (Assembling)

When the SHUTTER UNIT is rotated, the portion B of the LENS BARREL UNIT will project. Do not care
about the projection and keep rotating it. When it is rotated as far as it can go, the FRONT LENS UNIT
enters into the portion B of the LENS BARREL UNIT.

NOTE2 (Assembling)

When installing, use the original CCD HOLDER UNIT that has been removed from the original OPTICAL
UNIT.

Dowel

Dowel

Flexible board
of the SHUTTER UNIT

Large 

recepted

groove

Small 

recepted

groove

Large projected part

Small projected part

NOTE (Assembling)-1

NOTE (Assembling)-2

(1)-2

(1)-6

CCD HOLDER UNIT

LENS BARREL 
UNIT

FPC GUIDE

(1)-5

(1)-4

(1)-3

FPC GUIDE

s

METAL

M1.7

(SELF TAP)

4.5mm

XA4-9170-457

s

(1)-5

(1)-1

(1)-1

SHUTTER
UNIT

A

B

B

FRONT LENS 
UNIT

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands