manualshive.com logo in svg

Canon PowerShot G3, Service Manual

Share
Download
Canon PowerShot G3 Service Manual Download Page 79

3-7

CHAPTER 3.  REPAIR INSTRUCTION

Fig. 3-7 SIDE COVER, CF COVER

(1)-4

(2)-3

(2)-1

(1)-3

(1)-3

(1)-2

(2)-3

(1)-3

SIDE COVER 

JACK 
COVER

Claws

JACK COVER 
SHAFT

JACK COVER SHAFT

4.5mm

CD1-4854-000

DARK SILVER

M1.7

f

(1)-1

f

CF COVER

(2)-2

CF CLIPPING2
SPRING

XA4-5170-307

METAL

M1.7

(SELF TAP)

3.0mm

o

o

NOTE1 (Assembling)

NOTE2 (Assembling)

JACK COVER SHAFT does 
not overflow from the hole for 
inserting it.

While being careful 
not to ooze the 
Logenest rambda
A-74, coat it as
shown in the figure. 

2.2.4 SIDE COVER, CF COVER

(1) SIDE COVER

1. Remove the screw of 

f

.

2. Remove the SIDE COVER.
3. Push out the JACK COVER SHAFT with the thin stick like tweezers, and pull out the JACK COVER

SHAFT.

4. Remove the two claws and remove the JACK COVER.

NOTE1 (Assembling)

JACK COVER SHAFT is not overflow from the hole for inserting it (a dashed line).

(2) CF COVER

1. Remove the screw of 

o

.

2. Remove the CF CLIPPING2 SPRING.
3. Remove the CF COVER in the direction of arrow.

NOTE2 (Assembling)

While being careful not to ooze the Logenest rambda A-74, coat it as shown in the figure.

Summary of Contents for PowerShot G3


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands