Canon PowerShot G3 Service Manual Download Page 86

Page: 86 / 185

3-14

CHAPTER 3. REPAIR INSTRUCTION

Fig. 3-14 FLASH/JACK UNIT, SPEAKER UNIT

MAIN/FLASH
FPC

White

Red

(1)-3

(1)-2

(1)-1

(1)-2

METAL

M1.7

CB1-1998-000

3.0mm

(1)-5

(1)-6

(1)-4

(2)-2

(2)-1

SPEAKER BUSH

SPEAKER
UNIT

Dowels

Double-sided
adhesive tape

XA4-9170-359

BLACK

M1.7

(SELF TAP)

3.5mm

CAUTION

Be careful not
to drop the
SPEAKER BUSH.

NOTE3 (Assembling)

NOTE2 (Assembling)

NOTE-1 (Assembling)

FLASH/JACK UNIT

DC/DC CONVERTER
PCB ASS'Y

FLASH/JACK UNIT

(1)-2

2.2.11 FLASH/JACK UNIT, SPEAKER UNIT

(1) FLASH/JACK UNIT

1. Remove the MAIN/FLASH FPC.
2. Remove the cable of the BAT BOX UNIT and two cables of the FLASH/JACK UNIT.
3. Remove the three screws of

4. Remove the cable of the SPEAKER UNIT.
5. Remove the two screws of

6. Remove the two dowels and raise FLASH/JACK UNIT. Then push out the FLASH/JACK UNIT to the front

and remove the FLASH/JACK UNIT.

NOTE1 (Assembling)

Insert the cable coming from the BAT BOX UNIT to the red connector. Insert the cable coming from the
FLASH/JACK UNIT to the white connector.

(2) SPEAKER UNIT

1. Remove the SPEAKER BUSH.
2. Remove the SPEAKER UNIT from the FLASH/JACK UNIT.

CAUTION

Be careful not to drop the SPEAKER BUSH.

NOTE2 (Assembling)

Attach the double-sided adhesive tape at the position as shown in the illustration and install the SPEAKER
UNIT.

NOTE3 (Assembling)

Route the cable of the SPEAKER UNIT as shown in the illustration.

Summary of Contents for PowerShot G3


























































































































































































Search results

Summary of Contents for PowerShot G3

Reviews:

Brands by name

Popular brands

Canon PowerShot G3, Service Manual

Search results

Summary of Contents for PowerShot G3

Reviews:

Brands by name

Popular brands