Canon imageRUNNER Advance C2020i Basic Operation Manual Download Page 110

Page: 110 / 160

If the machine still does not operate normally, follow the procedure below, and

then contact your local authorized Canon dealer.

1. Turn the main power switch OFF.

2. Remove the power plug from the power outlet.

When you contact your local authorized Canon dealer, have the following information available:

Product name

Details of the malfunction

The error code displayed on the touch panel display

•

Setting the Limited Functions Mode from the Service Call

Message Screen

If the Service Call Message screen appears indicating a malfunction of a Finisher mode, you can clear it by turning the

Limited Functions Mode ‘On’ to temporarily limit the use of the finishing modes. When [Limited Functions Mode] is

displayed, follow the procedures below.

If you turn OFF the main power switch when there is a job waiting to print, that job is erased.

If you set Limited Functions Mode to ‘On’ from the Service Call Message screen, Limited Functions Mode in [Management

Settings] (Settings/Registration) is also set to ‘On’. (See e-Manual > Security.)

Press [Limited Fnctns Mode]

→

[Yes].

A message prompting you to turn the main power switch back ON appears.

Always grasp the power plug when disconnecting the power cord. Pulling on the power cord may

expose or snap the core wire, or otherwise damage the power cord. If the power cord is damaged,

this could cause current to leak, resulting in a fire or electrical shock.

Do not connect or disconnect the power cord with wet hands, as this may result in electrical

shock.

Summary of Contents for imageRUNNER Advance C2020i

































































































































































Search results

Summary of Contents for imageRUNNER Advance C2020i

Reviews:

Related manuals for imageRUNNER Advance C2020i

Brands by name

Popular brands

Canon imageRUNNER Advance C2020i, Basic Operation Manual

Search results

Summary of Contents for imageRUNNER Advance C2020i

Reviews:

Related manuals for imageRUNNER Advance C2020i

Brands by name

Popular brands