Bosch Rexroth R-IB IL 24 PSDO 8-PAC Manual Download Page 73

Page: 73 / 96

Technical Data and Ordering Data

DOK-CONTRL-ILPSDO8****-AW04-EN-P

Bosch Rexroth AG

71/

Rexroth Inline Module with Safe Digital Outputs R-IB IL 24 PSDO 8-PAC

11.4

Ordering Data

11.4.1

Ordering Data: Safety Module

11.4.2

Ordering Data: Documentation

Description

Order code

MNR

Pcs. / Pkt.

Rexroth Inline module with safe digital outputs

R-IB IL 24 PSDO 8-PAC

R911172847

For additional ordering data (accessories), please refer to the product catalog

www.boschrexroth.com/electrics

Description

Order code

MNR

Pcs. / Pkt.

Inline

“Automation terminals of the Rexroth Inline product

range” application description

DOK-CONTRL-ILSYSINS***-AW..-

EN-P

R911317021

PROFIsafe

"PROFIsafe - Profile for Safety Technology on PROFI-

BUS DP and PROFINET IO, Version 2.4, February

2007" specification

See

http://www.profisafe.net

Make sure you always use the latest documentation.

It can be downloaded at

www.boschrexroth.com/electrics

Documentation for PROFIsafe, PROFIBUS, and PROFINET is available on

the Internet at

www.profibus.com/pall/meta/downloads

Summary of Contents for Rexroth R-IB IL 24 PSDO 8-PAC

































































































Search results

Summary of Contents for Rexroth R-IB IL 24 PSDO 8-PAC

Reviews:

Brands by name

Popular brands

Bosch Rexroth R-IB IL 24 PSDO 8-PAC, Manual

Search results

Summary of Contents for Rexroth R-IB IL 24 PSDO 8-PAC

Reviews:

Brands by name

Popular brands