Bosch Rexroth R-IB IL 24 PSDO 8-PAC Manual Download Page 31

Page: 31 / 96

Inline Potential and Data Routing, and Inline Connectors

DOK-CONTRL-ILPSDO8****-AW04-EN-P

Bosch Rexroth AG

29/

Rexroth Inline Module with Safe Digital Outputs R-IB IL 24 PSDO 8-PAC

4.3

0 V (GND)

Channel 1 and channel 2

3.4

4.4

Terminal point

Signal

Channel assignment

LED

5.1

OUT2_Ch1

Output 2, channel 1

2.1

6.1

OUT2_Ch2

Output 2, channel 2

2.2

5.2

Not used

6.2

Not used

5.3

0 V (GND)

Channel 1 and channel 2

6.3

0 V (GND)

Channel 1 and channel 2

5.4

6.4

Fig. 4-5

Terminal point assignment for connector 3

Terminal point

Signal

Channel assignment

LED

7.1

OUT3_Ch1

Output 3, channel 1

3.1

8.1

OUT3_Ch2

Output 3, channel 2

3.2

7.2

Not used

8.2

Not used

7.3

0 V (GND)

Channel 1 and channel 2

8.3

0 V (GND)

Channel 1 and channel 2

7.4

8.4

Fig. 4-6

Terminal point assignment for connector 4

Loss of functional safety due to parasitic

voltages

Connect the ground of the actuator to the ground terminal point of the

corresponding output on the Inline connector. An external ground may not be

used.

Terminal point

Signal

Channel assignment

LED

Fig. 4-4

Terminal point assignment for connector 2

WARNING

Summary of Contents for Rexroth R-IB IL 24 PSDO 8-PAC

































































































Search results

Summary of Contents for Rexroth R-IB IL 24 PSDO 8-PAC

Reviews:

Related manuals for Rexroth R-IB IL 24 PSDO 8-PAC

Brands by name

Popular brands

Bosch Rexroth R-IB IL 24 PSDO 8-PAC, Manual

Search results

Summary of Contents for Rexroth R-IB IL 24 PSDO 8-PAC

Reviews:

Related manuals for Rexroth R-IB IL 24 PSDO 8-PAC

Brands by name

Popular brands