BMW K 1100 LT Page 94 Repair Manual Download

Page: 94 / 364

12.8

Removing and installing ignition
coils

•

Disconnect earth (ground) lead of battery and in-
sulate.

•

Remove top (1) and bottom (2) ignition coil cover.

•

Disconnect plug connector (3) at the ignition
coils.

•

Disconnect plug connector (4) for terminal “1”
and “15”.

•

Release earth (ground) connection (5) on starter.

•

Release top and bottom mounting at intermedi-
ate flange (6).

•

Install in the reverse order of removal.

Note:

Note assignment of ignition leads to ignition coil. Ig-
nition coils are also marked.

Tightening torque:

Ignition coils to intermediate flange ................ 5 Nm

LT120050

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for K 1100 LT













































































































































































































































































































































































Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands

BMW K 1100 LT, Repair Manual

Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands