manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 65 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 65

11.31

Removing output shaft

Removing oil sump

•

After removing the screws, loosen the seal with 
light blows of a plastic-faced hammer.

Removing oil filter

•

Unscrew oil filter (1) with the oil filter wrench, 

BMW No. 11 4 650

.

Removing lower section of crankcase

•

Take out retaining screws and screws (3) holding 
the output shaft.

•

With light blows of a plastic-faced hammer, loos-
en the gasket and take off the lower section of 
the housing. Note presence of O-rings.

•

Carefully lift out the output shaft; the needle roller 
bearing and circlip are loose on the shaft.

LT110440

2

3

1

Removing and installing oil level sight glass

•

Pierce the plastic disc with a large screwdriver 
and lever out the oil level sight glass.

•

Oil the sealing face of the oil level sight glass 
lightly and drive it in with a drift, 

BMW No. 00 5 550

.

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments