manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 26 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 26

00.18

Checking clutch clearance and 
adjusting if necessary

Inspections I, III

•

Detach clutch cable at clutch release lever (1).

•

Slightly push back rubber sleeve (2).

•

With the aid of setting gauge, 

BMW No. 21 3 500

,set dimension “b” with ad-

justing screw at clutch hand lever.

Dimension “ B ” ..... 75 ± 1 mm (2.952 ± 0.03937 in)

•

Reattach clutch cable at clutch release lever. 

•

Using box spanner, 

BMW No. 21 3 610

,release 

locknut (6) of adjusting screw (7) at clutch re-
lease lever.

•

Unscrew adjusting screw by one to two turns, 
then screw in until pressure can be felt.

•

Lock adjusting screw with locknut.

•

Set dimension “A” with adjusting screw at clutch 
hand lever.

•

Lock adjusting screw (5) with knurled nut (3).

Dimension “A” ........ 4 ± 0.5 mm (0.157 ± 0.0197 in)

e

 Caution:

Adjust to take up wear only at the adjusting screw 
on the clutch release lever.

Reading out Motronic defect code 
memory

Inspections II, III

•

Carry out this job only on motorcycles with cata-
lytic converter.

L

 Note:

To read out Motronic defect code memory, see the 
booklet entitled: 
“BMW Diagnosis, Motronic 2.1 with oxygen-sensor 
control” (order No. 01 70 9 798 970).

LT000160

2

1

B

LT000170

7

6

LT000180

5

4

3

A

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments