BMW K 1100 LT Page 53 Repair Manual Download

Page: 53 / 364

11.19

Removing timing chain cover

Removing the Hall-effect signal transmitter

•

Remove cover (1).

•

Take off gasket (2).

•

Remove Hall-effect signal transmitter (3), noting
the semi-circular shim washers.

Note:

Mark the correct installed position of the adjusting
washer on the engine block, or remove it in the TDC
position.

•

Remove gate rotor (4) and take off adjusting
washer (5).

Remove the crankshaft cover

•

Detach the coolant hose at the water pump and
radiator.

•

Remove the cover.

Removing cylinder head cover

•

Remove the ignition leads.

•

Remove the cylinder head cover.

Removing and installing sealing ring in timing
case cover

•

Drive the sealing ring out with a suitable drift.

•

Drive the sealing ring in from the inside using
handle,

BMW No. 00 0 500

, and drift,

BMW No. 11 1 610

LT110200

LT110210

Downloaded from

www.Manualslib.com

manuals search engine

Summary of Contents for K 1100 LT













































































































































































































































































































































































Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands

BMW K 1100 LT, Repair Manual

Search results

Summary of Contents for K 1100 LT

Reviews:

Related manuals for K 1100 LT

Brands by name

Popular brands