manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 85 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 85

11.51

•

Connect the engine wiring harness (coolant stub 
pipe, throttle position sensor, CO detector, injec-
tors, air cleaner housing).

•

Attach cable straps (three) at fuel injection rail.

•

Attach wire cables for increased idle speed and 
throttle operation.

Throttle cable play....................... 0.75 mm (0.03 in)

•

Install the radiator.

•

Install the left engine bulkhead (1).

•

Attach cable strap (2).

•

Install fuel line (3).

•

Install right engine bulkhead (4).

•

Attach cable strap (5).

•

Install coolant line (6) in bulkhead.

•

Install driveline.

•

Install fuel tank.

•

Install radiator surround.

•

Install left and right side sections.

•

Install storage compartment.

•

Install knee pads.

1

2

3

LT110770

4

5

6

LT110780

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments