manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 209 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 209

31.7

Removing and installing bearing outer 
race in steering head

Removing bearing outer race

•

Remove bearing outer race (1) using extractor 
BMW No. 00 5 560 (2), and support ring 
BMW No. 31 4 800 (3).

e

 Caution:

Bearing and bearing outer race belong together, 
always fit together!

Installing bearing outer race

•

With the aid of the spindle of the frame test 
gauge,  

BMW No. 46 5 604/605

, in conjunction 

with the thrust piece, 

BMW No. 31 4 820

, install 

bearing outer race (4) together with hexagon nut 
and washer to the limit stop.

31 4 800

LT310050

00 8 560

1

46 5 604

LT310060

46 5 605

4

31 4 820

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments