manualshive.com logo in svg

BMW K 1100 LT, Repair Manual

Share
Download
BMW K 1100 LT Repair Manual Download Page 69

11.35

Assembling the crankcase

•

Install O-rings (6,7) for the water and oil passag-
es.

•

Coat the sealing faces (which must be free from 
oil and grease) lightly with

 3-Bond-1209

.

•

Place the two halves of the housing together.

•

Screw in bearing bolts (4, 5) for the shouldered 
and needle roller bearings, and tighten alternate-
ly.

X 

Tightening torques:

Shouldered bearing (4) ................................. 40 Nm
Needle roller bearing (5) ............................... 18 Nm
Retaining screws of two halves of the housing7 Nm

1

2

3

4

5

LT110530

6

7

KR110521

Installing oil mesh strainer

•

Note presence of O-ring (2).

Installing oil filter

•

Coat the oil filter sealing ring with oil.

•

Do not tighten the oil filter more than half a turn 
beyond the point where it makes contact.

Installing oil sump

•

Coat the sealing faces (which must be free from 
oil and grease) with 

3-Bond 1209

.

X 

Tightening torques:

Retaining screws............................................ 7 Nm
Oil filter......................................................... 11 Nm

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands