manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 281 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 281

34.23

Dismantling and assembling rear 
brake caliper

Dismantling rear brake caliper

•

Remove keepers (1).

•

Drive out spring (2) and retaining pin (3). 

•

Take out brake pads.

•

Seal the bleed screw.

X 

Tightening torque:

Bleed screw at brake caliper rear ................. 11 Nm

•

Remove sealing rings (4) from left/right cylinder.

e

 Caution:

Keep fingers away from gap between pistons and 
side contact face of brake pads; risk of injury! 
If necessary press back with screwdriver carefully.

•

Hold a cloth over the brake caliper piston.

•

Carefully 

press out brake piston (6) with a com-

pressed air gun applied to the connecting bore; 
work at low air pressure.

•

Remove sealing rings (5) from left/right cylinder 
hole.

Assembling rear brake caliper

•

Coat the new sealing rings with brake fluid and 
insert them into the left/right brake caliper cylin-
ders.

e

 Caution:

Do not tilt the brake pistons when installing.

•

Coat both brake caliper pistons with brake fluid 
and install them.

L

 Note:

The installed position must be correct!

•

Insert brake pads and secure with retainers.

LT340290

2

1

3

4

6

6

5

5

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments