manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 270 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 270

34.12

Removing and installing front brake 
line

Removing upper brake line

•

Drain brake system.

•

Remove fuel tank.

•

Release brake line (1) at handbrake cylinder.

•

Remove cover for brake distributor on mud-
guard.

•

Release brake line at the distributor.

•

Install in the reverse order of removal.

L

 Note:

Secure brake line to handbrake cylinder such that it 
does not chafe or kink when the handlebar is turned. 
Replace sealing rings of brake lines.

e

 Caution:

Ensure brake fluid does not come in contact with 
painted parts of the vehicle; brake fluid destroys the 
paintwork.

Removing lower brake line

•

Remove rear section of mudguard.

•

Release brake line at distributor and at the brake 
caliper.

•

Install in the reverse order of removal.

L

 Note:

Replace sealing rings of the brake lines.

•

Carefully bleed brake system.

X

 Tightening torques:

Brake line to handbrake cylinder .................. 18 Nm
Brake line to distributor ................................ 18 Nm
Brake line to brake caliper............................ 18 Nm
Bleed screw ................................................. 14 Nm

LT340090

1

LT340100

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments