manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 56 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 56

11.22

Removing, stripping down and assem-
bling cylinder head

Removing camshafts

•

Remove the bearing caps (1) for the thrust bear-
ings first, to prevent tilting.

•

Release tension uniformly at radial bearing
caps (2) and remove them.

•

Take out the camshafts.

Removing cylinder head

•

Unscrew the cylinder head bolts (3) with Torx in-
sert, 

BMW No. 00 2 610

.

•

Strike the cylinder head lightly with a plastic-
faced hammer to dislodge it.

Removing bucket-type tappets

•

Using special suction tool, 

BMW No. 11 3 251

, 

pull bucket tappets (5) out of the cylinder head.

•

Make a note of which tappet belongs to which 
valve.

4

3

1

2

5

LT110270

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments