manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 153 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 153

17.11

Troubleshooting

Coolant temperature warning lamp lights 
up.

no

Check coolant in expansion tank.
Is coolant level too low?

yes

Top up coolant.

no

Check thermostat.
Is thermostat defective?

yes

Replace thermostat.

no

Check water pump.
Is water pump defective?

yes

Repair/renew water pump.

Fan motor does not switch on.

no

Check fuse F7.
Is fuse defective?

yes

Renew fuse.

no

Check fan relay.
Is fan relay defective?

yes

Replace fan relay.

no

Check power circuit.
Does circuit have poor contact/break?

yes

Make contact/repair break.

no

Check fan motor.
Is fan motor defective?

yes

Repair/renew fan motor.

no

Check thermostat.
Thermostat does not open?

yes

Replace thermostat.

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments