manualshive.com logo in svg

BMW K 1100 LT, Repair Manual, Page: 198 / 364

Share
Download
BMW K 1100 LT Repair Manual Download Page 198

23.24

Installing transmission cover

•

Knock out cap (arrow) from the inside using a 
drift.

•

Heat up transmission cover to 100°C.

•

Parting surface at housing and cover must be 
clean and free of grease.

•

Thinly coat one of the two parting surfaces with 

Loctite 574

 or with 

Three-Bond 1209

.

•

With the aid of a drift or screwdriver, press back 
locking lever in direction shown by arrow.

•

Carefully fit cover on the housing.

•

Screw in screws holding transmission cover and 
firmly tighten.

X 

Tightening torque:

Retaining screws for cover

............................. 9 Nm

•

Thinly coat end cap (arrow) with 

Three-Bond 1209

 and knock in with drift by 

8 mm (0.31496 in).

•

Fit idle lock (ball and spring) in idle position.

•

Screw in screw for idle lock coated with 

Loctite 243

.

X 

Tightening torque:

Screw for idle lock

........................................ 13 Nm

LT230420

LT230370

LT230380

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Summary of Contents for K 1100 LT













































































































































































































































































































































































Reviews:

No comments